Loading... Please wait...
Click the image above to see a larger version
  • Image 1
  • Image 2
  • Image 3
  • Image 4

Kakute HolyBro F4 V2 OSD v1.3 with Tekko32 4 in 1 ESC AU USA

$75.00
Shipping Weight:
150.00 Grams
 
Stock Remaining:
8


Product Description

Kakute F4V2 FC and Tekko32 4in1 ESC Combo


The Holybro Kakute F4V2 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster F4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization! Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS, FPort and SmartPort at the same time. The Kakute F4 is designed to support all serial protocols at once.

Holybro Kakute F4 V2 flight controller runs BetaFlight 3.4 AU  , this FC integrates OSD.

  1. F4 flight controller (FC) , BlackBox, Soft mounted IMU, and
  2. on-screen display (OSD) in one.

Specs

  • MCU: STM32F405RGT6 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 5 hardware UARTS (UART1,3,4, 5, 6)
  • Supports serial receivers (SBUS, FPort, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 35x30x8mm (includes USB in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 7g 
  • FLIGHT MANUAL in English pdf (by Joshua B) here
Description:

The Holybro Kakute F4 V2 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in one. The Kakute F4 V2’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.
 
New V2 Features
· Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras such as the Foxeer Arrow, etc.
· Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.
· Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
· Barometer (BMP-280) sensor on board allows altitude hold mode.
· I2C pad available for certain external sensors.
 
Features
· Supports Betaflight and Cleanflight.
· Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
· Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
· New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
· 2 oz. copper PCB allows up to 120A maximum continuous current.
· Dedicated bootloader button for easy firmware flashing.
· Low-profile design fits into even very compact frames.
· FC powered by the Tekko ESC.
· Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 V2 monitors voltage directly from the Tekko ESC battery power lead.
· Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
· Supports BLHeli pass-through for easy ESC upgrade and configuration.

Also can be flashed with iNav..... Supports i2c compass and UART GPS connection and integration....

 

Tekko32 4-in-1 35A ESC


Powerful 4in1 ESC with BLHELI32 firmware natively supports ESC Telemetry function.

Features:

  • 4in1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware.
  • On this version added more CAPS to reduce power noise.
  • 32bit ESC with BLHELI32 firmware
  • 4PWM input
  • Voltage output (VBAT), ESC Telemetry(TELEM)
  • Supports Oneshot / Multishot / Dshot PWM
  • Supports damped light
  • NO BEC

 
Specs

  • Supports 3-6S lipo input
  • 35A continuous current, 50A burst
  • Mounting holes 30.5x30.5mm
  • Size:55*40*6.4mm
  • Weight 17g

 

Some Tips:


BLHeli_32 ESC Firmware Overview
What is Dshot1200 and Why Dshot1200 is Better?
How to Get Dshot1200 Running in Betaflight?


 

In Order to reduce EMI/EMC interference to the FPV link, it is recommended to shield the FETs with Copper Tape. 

Kakute F4 V2 & Tekko 32 4in1 esc (BLHeli 32)  Combo

 

Downloads:


Download the latest BLHeli_32 Configurator and BLHeli_32 user manual here.

 

Perfect FC/ESC combo for Knife 200/240/280


scarab-knife-200.jpg  knife-240.jpg

 

Package Includes

  • Kakute F4 V2 FC board *1 
  • spare flex cable IMU*1 
  • spare IMU Foam*3 
  • Tekko32 4in1 ESC running DShot1200
  • FC - ESC connection cable (8 pin to 8 pin 1mm pitch).

Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!




Currency conversion