Loading... Please wait...
- Home
- Products
- New
- Blog
- Wiki
- Shipping
- Newsletter
- Contact
-
Tech FAQ
- Connect AIR3 to TBS Crossfire Rx
- How to use FC LiPo Voltage for AIR3 iNav OSD
- How to re-flash AIR3 iNAV bootloader
- Calibrating RC Transmitter Tx - for PARIS AIR3 iNav BetaFlight
- FrSky R-XSR Firmware Update Proceedure
- Knife 200/240 - building guide
- tricopter build guide Scarab 660
- Scarab QuadOcta building guide
- Failsafe RC setup - What is the best way to set up failsafe for a Naze Quad
- My ESCs are hot - Why is only one red wire required for 5v ESC BECs connected in parallel
- My Quad copter with Naze / AIR Hero•32 is twitching
- how do I trim my PARIS Sirius™ Air HERO•32 miniQuad Controller naze board BaseFlight
- Which FrSky Rx receivers does the Taranis (with X9D internal module) support
- What is the best FPV Tx for a beginner
- Scarab Knife - Seperate BEC needed to run off opto 18A ESC
- How do i use Ch9 Sbus on Taranis X8R / PARIS v5r3 Mega to control camera tilt on my servo gimbal pin 44
- My Quad - with Hero v2 is tail wagging - how to fix
- Quad motor suddenly stopped/stuttered - my Quad flipped - was ok before
- How can I get my Taranis X8R to use S-Bus 1-8 and other pins 9-16 for camera gimble tilt, roll and shutter
- How do i reverse a MultiWii Tricopter tail servo direction Air v2
- What is the difference between a Quad Flipping vs a Quad Flopping down
Hi everyone, We are back. We are busy filling orders, and ready to answer any questions regarding any of our products.
Thanks to all our valued existing and new customers.-->
|
|
|
- Home
- Propellors
- HQProp Durable 4x4.5x3B CW/CCW - BLACK - 4 props
- Home
- Propellors
- Props 4"
- HQProp Durable 4x4.5x3B CW/CCW - BLACK - 4 props
Product Description
HQ Prop AU new DURABLE 4x4.5x3" props (June 2016) 0445 triples HQProp DP 4x4.5x3B - 2xCW(R) + 2xCCW(standard? BLACK mini quad racing FPV props. These are specifically matched to Scarab Knife 200 - They require no balancing - They are EXTRA tough and quite.
Features
- SUPER STRONG - Durable ABS plastic
- light weight 4grams/ prop - perfect for rapid speed changes - required to stabilise multiwiicopters
- Suits 3100kv - or 3200kv on 4S - CarbonBird® motors with 5mm hub
- 5mm ID Ø bore
- Requires 7.3mm shaft height ; 5mm Ø diameter shaft to mount it.
- require almost no balancing (always check every prop and use 800 grit wet-n-dry to remove any sharp edges at the leading edge of the blades)
Includes
- includes 4 props 4x4.5" triples as you see in Photo 1 at top right - BLACK - 2*CW(R) and 2*CCW triples = total 4
Excludes
We recommend to always check Balancing - These HQProps are near perfect as supplied (true centres) - they require almost no balancing, if any at all - However you must check each and every prop yourself - BEFORE FLYING - on a balancer - we found none in 4 set needed balance - but its up to the user to check and if necessary balance for HD Video
Limitations - Do not exceed the max RPM 29,500 - replace any prop if damaged or crashed - You must understand the risk of flying a Quad with a damaged prop can result in the Multicopter crashing/falling and hurting a 3rd party or yourself - YOU WILL BE RESPONSIBLE for this ! - props can cut - keep away from eyes! wear safety glasses ALWAYS !
Keep your PROPS OFF - not installed - until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. PROPS can CUT ! take precautions ! Never fly closer than 30m to/from any person or pet
Question - Can it use this prop on other motors - ?
Check the diameter of your motor shaft is 5mm and the depth between the spinner and the base <7mm or less - then you can pop them straight on.
